{"id":2260,"date":"2015-10-31T11:00:40","date_gmt":"2015-10-31T16:00:40","guid":{"rendered":"http:\/\/protofusion.org\/wordpress\/?p=2260"},"modified":"2015-11-03T09:40:48","modified_gmt":"2015-11-03T14:40:48","slug":"diy-3d-printed-model-rocket","status":"publish","type":"post","link":"http:\/\/protofusion.org\/wordpress\/2015\/10\/diy-3d-printed-model-rocket\/","title":{"rendered":"DIY 3D-Printed Model Rocket"},"content":{"rendered":"
\"IMG_1778\"<\/a>

3… 2… 1… Blast off!<\/p><\/div>\n

Space has often been referred to as\u00a0the final frontier, and many who look towards the heavens find themselves wondering what might be hiding just beyond our reach. Although commercial space missions cost well into the millions and even\u00a0billions of dollars, model rocket enthusiasts have been striving\u00a0to reach\u00a0just a bit closer to space for decades. Estes model rockets have allowed generations of kids to dream about one day escaping the earth’s gravity and venturing into the unknown. I\u00a0like to think that a bit of exploratory spirit can be found in everyone, and I am\u00a0certainly no exception.<\/p>\n

\"IcarusWe all know that when you have a hammer, everything starts to look like a nail, and the same is true of 3D printers. When we first acquired a 3D printer, our first thought was: “why don’t we print a rocket?” And here we are. Since anyone can buy off-the-shelf components and put a rocket into the air, we opted for a slightly more challenging approach\u00a0by attempting to make\u00a0every component of the rocket ourselves\u00a0–\u00a0including engines, igniters, and launch system. This post details our progress so far – after a handful of launch attempts we have successfully\u00a0made\u00a0every\u00a0component\u00a0except the engines (we’ve been using Estes model rocket engines until we can create a suitable replacement).<\/p>\n

CAD Drawings<\/h3>\n

The rocket body consists of several modular pieces that were designed to be somewhat configurable and interchangeable. The tail piece has 4 identical fins that slide into place using a friction fit, and an engine stop that slides inside\u00a0(which can be adjusted based on the type of engine). The body pieces then lock into place on top of the tail assembly. The number of body pieces used determines the height of the rocket, and guide rings for the launch pad can be fitted on to keep the rocket going straight. A flame shield (a\u00a0replacement for\u00a0the normal recovery wadding)\u00a0slides down into the body to protect the parachute from the ejection charge. And finally the nose cone goes on top.<\/p>\n

\"Rocket<\/a>

Rocket Body<\/p><\/div>\n

\"Rocket<\/a>

Rocket Fin<\/p><\/div>\n

\"\"<\/a>

Rocket Nose<\/p><\/div>\n

CAD files for\u00a0printing the rocket are available in the Profusion repo<\/a>. All CAD work by Bryan Den Hollander.<\/p>\n

Wireless Launch System<\/h3>\n
\"Remote<\/a>

Wireless Remote Launch System<\/p><\/div>\n

In keeping with the DIY theme we wanted to avoid buying an off-the-shelf launch system, so we started off using a 12V battery and some long wires, shorting the\u00a0igniter\u00a0across the battery to activate it. This quickly became cumbersome, mainly\u00a0due to\u00a0the limiting length of the lead wires, so we decided to build a wireless system. Some unused\u00a0Xbees we had laying around became the obvious choice for a quick and easy wireless link, and the rest of the design choices were similarly dictated by parts on hand.<\/p>\n

Remote<\/h4>\n
\"launch-system-remote\"<\/a>

Launch System Remote Schematic<\/p><\/div>\n

The remote is a handheld device powered by a single lithium primary cell (3.6V, 2400mAh) and contains nothing more than an Xbee, a few buttons and switches, and their corresponding LEDs. The\u00a0power switch turns on the Xbee, and the arm switch communicates an armed status to the base and allows the fire button to be triggered. The arm and trigger inputs are sent to the base station using the Xbee’s built-in line passing, which essentially\u00a0mirrors I\/O state on two or more Xbee modules. To verify\u00a0communication with the base when arming, the arm input is sent to the base and then relayed back to the remote. The circuit is detailed in the schematic above.<\/p>\n

Base<\/h4>\n
\"launch-system-base\"<\/a>

Launch System Base Unit Schematic<\/p><\/div>\n

The base station is powered by a much beefier 3S lithium battery pack (11.1V, 2600mAh), due to the large amount of power required to set off an igniter. It also has an Xbee, which receives line passing signals from the Xbee in the remote. When the trigger is activated, a p-channel mosfet is turned on to allow current to flow through the output (and to the igniter). Status LEDs indicate the state of the base unit.\u00a0The circuit schematic above\u00a0gives the full picture.<\/p>\n

Igniters<\/h4>\n
\"DIY<\/a>

DIY Igniters<\/p><\/div>\n

A DIY launch system isn’t complete without homemade igniters, so we\u00a0acquired some nichrome wire<\/a>\u00a0and\u00a0pyrodex (black powder substitute) to make our\u00a0own. By twisting a bit of\u00a0nichrome\u00a0between two copper leads, and then dipping the tip in superglue before coating with a pinch of pyrodex, electric\u00a0igniters\u00a0can be made by the dozens for just pennies.<\/p>\n

Launch Video<\/h3>\n